POM系列油墨
品牌：MY INK 名稱：POM油墨 編號：984646
POM賽鋼料系列油墨采用高級進口丙烯酸樹脂和高級顏料經過細制研磨加工組合而成，適用于PA（尼龍）、POM（賽鋼）、電木、PBT、纖維合成、工程塑料、合成塑料等各種熱固性塑膠制品的絲印及移印，無需加固化劑，即可獲得優異的附著力。
油墨特性：
1、平光、附著力佳、耐汽油、酒精、耐化學品；
2、手感好，流平性佳、面光潔；
3、表面硬度好，耐沖擊性能強、抗刮傷；
4、耐汽油、耐酒精、耐化學品程度佳；
印刷條件：
選用網目為100-350目，以120T網布計算印刷覆蓋面積每公斤約30~35㎡。
表干時間自然揮發10-15分鐘，實干時間在24小時以內，48小時后達最佳性能，取決于操作時的實際溫度，建議烘烤方式。
1．用本公司專用稀釋劑開油，718洗網水洗網
2．無需處理，單組份,為了確保產品質量，建議使用印刷前使用溶劑清洗產品外觀印刷部位。
3．烤箱130℃-180℃實際溫度烘烤30-50分鐘產品效果達最優性能。
測試方法（完全干燥后）：
1、3m膠紙粘在畫有百格的油墨表面，45度角迅速拉起3次不脫油;忽視刮刀邊緣油墨脫離
2、純度99%的工業酒精，一千克砝碼用棉布包住在油墨表面，以水平力來回摩擦30次無脫色;
3、 耐磨：橡皮擦500g力水平來回擦300次。
使用方法：
1．建議用我公司專用稀釋劑進行稀釋，不建議使用783慢干稀釋劑稀釋，使用前應充分攪拌，用后隨時密封。
2．攪拌時加本公司配套開油水10-12%，稀釋到印刷適合粘度，移印稀釋使用移印專用稀釋劑；用718洗網水清洗。
3．不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。
注意事項：
1．各種承印物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。
2．在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可;
3．環境溫度過高，將會影響油墨原有質量。白色超越150都會變色，烘烤時請用木質材料墊底進行烘烤，不得直接接觸鐵
4．根據氣候變化，請遠離火源，陰暗處15度-30度環境下存放
Brand: but MY product name: POM INK Numbers: 6486694
POM series ink
The steel material series as POM ink advanced import acrylic resin and senior pigment after fine grinding system, used in combination to PA (nylon), POM (" steel), bakelite, PBT, synthetic fiber, engineering plastic, synthetic plastic, etc. Various kinds of thermosetting plastic products of screen and pad printing, need not add curing agent, can obtain excellent adhesion.
Ink characteristics:
1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals;
2, feel is good, flow ping sex, good surface is bright and clean;
3 and fine surface hardness, impact resistance properties of strong, resistance to scratch;
4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good;
Printing conditions:
Choose for 100-350 mesh mesh to 120 T nets cloth printing coverage area per kilogram computation about 30 to 35 ㎡.
Dry time table natural volatile for 10 or 15 minutes, action in time within 24 hours, 48 hours after the best performance, depends on the operation of the actual temperature, suggest baking mode.
1. With our company special thinner open oil, 718 water wash nets nets
2. Not processing, one part, in order to ensure product quality, it is recommended to use use before printing solvent cleaning product appearance printing area.
3. Preheat the oven to 130 ℃ to 180 ℃ temperature baking actual 30 to 50 minutes product effect of optimal performance.
Test method (dry) :
1, 3 m stuck in the picture has the tape's ink surface, the 45 o Angle quickly pull up three times not to take off the oil; Ignore scraper edge from ink
2 and purity, 99% of industrial alcohol, a kilogram of Jordan farmar cover with cotton cloth in ink surface to horizontal force friction 30 times back and forth without decoloring;
3, wear-resisting: the eraser 500 g force level wipe 300 times back and forth.
Method of use:
1. The proposal with my company special thinner to dilute, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing.
2. Add the company supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718.
3. Not with other kinds of printing ink mixed use, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon.
Note:
1. All kinds of printing material appearance similar, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production.
2. In moving printing process, such as a wire drawing or away, can be appropriately to add some slow dry paste can;
3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron
4. According to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for
