( 1) 故障現象一: 按下割炬開關(K3 ) 后, 機內繼電器(J 1) 不吸合。 ①故障分析 1: 割炬開關(K3 ) 損壞或斷線; 排除方法: 檢修或更換割炬開關(K3) 。 ②故障分析 2: 溫度繼電器(V K ) 失控或損壞;排除方法: 檢修或更換溫度繼電器③故障分析 3: 繼電器(J 1) 線圈短路; 排除方法在日常使用中割炬開關(K3 ) 損壞或斷線是常見現象, 檢查故障時應先檢查K3。
更多詳細內容請登陸:www.pmqgj.net 泊頭市明澤數控機械廠
數控泡沫切割機、歐式線條切割機、EPS泡沫切割機 泡沫切割機
空氣等離子弧切割機俗稱等離子切割機, 是客車制造企業廣泛使用的一種高效切割設備。KL G40 型空氣等離子弧切割機將工頻三相交流電源(380 ) , 經高頻變壓、三相橋式整流, 再經整流濾波輸出高頻電流。采用高頻引弧器引燃等離子弧, 當高溫的等離子弧和高速的壓縮氣流通過割炬噴嘴小孔時, 使電弧的熱能集中 壓縮 程度提高而將被切割金屬表面局部熔化, 并同時用高速氣流將融化的金吹走, 從而形成狹窄切口。
更多詳細內容請登陸:www.pmqgj.net 泊頭市明澤數控機械廠
數控泡沫切割機、歐式線條切割機、EPS泡沫切割機 泡沫切割機
(1) a fault phenomenon: press cut torch switch (erp), machines relays (J 1) don't suck $. (1) the fault analysis 1: cut torch switch (erp) damage or break; Elimination method: repair or replace cut torch switch (erp). (2) the fault analysis 2: temperature relays (V K) out of control or damage; Elimination method: repair or replace temperature relay (3) failure analysis 3: relay (J 1) coil short circuit; Elimination method in the daily use of the torch switch (erp) cut damage or break line is a common phenomenon, check the fault should be first check erp.
More details please visit: www.pmqgj.net botou MingZe CNC machinery factory
Numerical control foam cutting machine, Europe type line cutting machine, cutting machine foam cutter EPS foam
Air plasma arc cutting machine commonly known as plasma cutting machine, is widely used in the enterprise coach manufacturing a kind of high efficient cutting equipment. KL G40 type air plasma arc cutting machine will work three-phase ac power frequency (380), the high frequency variable pressure, three-phase bridge rectifier, then through rectifier filter output high-frequency currents. With high frequency arc ignites plasma arc, when the temperature of the plasma arc and high-speed airflow through the compression of the torch cut nozzle holes, and make the arc on improved heat compression and will be cutting metal surface melting, and at the same time use the local high-speed airflow would melt gold blown away, so as to form the narrow incision.
More details please visit: www.pmqgj.net botou MingZe CNC machinery factory
Numerical control foam cutting machine, Europe type line cutting machine, cutting machine foam cutter EPS foam