簡介General Description
此液壓微型動力單元由高齒輪油泵、直流電機、多用集成塊、液壓閥、油箱等零部件有機組合為一體。通常用作托盤車、輕型堆高車的動力源。電磁卸荷閥卸荷實現回油，下降速度由內置性平衡閥控制。
Consisting of high pressure gear pump, DC motor,a multi-functional manifold, valvesand a tank.This power unit has a power up a gravity down circuit.It is widely used in pallet tuck and light fork lift.
外型尺寸Outline Dimension 系統工作原理Hydraulic Circuit Diagram
型號規格說明Model Specifications
型號 Model | 電機電壓 Motor Volt | 電機功率 Motor power | 名義轉速 Rated Speed | 油泵排量 Displacement | 溢流閥壓力 System pressure | 油箱容量 Tank Capacity |
RBZ-E0.5W1T2-1 | 12VDC | 0.8KW | 2500RPM | 0.63mL/r | 16MPa | 1L |
RBZ-E0.63W1T2-1 | 12VDC | 0.8KW | 2500RPM | 0.8mL/r | 16MPa | 1L |
RBZ-E0.5A1T2-1 | 24VDC | 0.8KW | 3500RPM | 0.63mL/r | 16MPa | 1L |
RBZ-E0.63A1T2-1 | 24VDC | 0.8KW | 3500RPM | 0.8mL/r | 16MPa | 1L |
說明：
1.如需不同流量的泵、壓力、電機功率等系統參數，請查看液壓動力單元型號說明。
1.Please go to page 1 or consult our sales engineer for the different pump displacement,motor power or tank capacity.
2.如需手動應急放油裝置，請在訂貨時說明。
2.The manual override function is available on request.
注意事項Special Notes
1.本動力單元為S3工作制，不可連續運轉，30秒開，270秒停。
1.The duty of this power unit is S3,ie.,30seconds on and 270 seconds off.
2.安裝前必須保證油缸、油管、接頭等液壓元件清潔無任何雜質粘附。
2.Clean all the hydraulic parts concemed before mounting the power unit.
3.液壓油粘度應為15-68CST，應清潔無雜質，推薦使用N46號液壓油。
3.The viscosity of the oil shoud be 15-68 cst.
4.系統使用第一個100小時后，應更換液壓油，以后每3000小時更換一次液壓油。
4.Change the oil after the first 100 hours of using the power unit,then change the oil every 3000 hours.
5.本液壓動力單元適用于立式安裝。
5.This power unit should be mounted vertically.
6.首次啟動運行系統時，應立即檢查油箱中的油量是否充足。
6.Check the oil level in the tank after the first star of the power unit.
