Z41H美標法蘭閘閥特點
Z41H美標法蘭閘閥流體阻力小，適用的壓力、溫度范圍大，介質流動方向不受限制，密封性能良好。
Z41H美標法蘭閘閥安裝要點
1）、安裝位置、高度、進出口方向必須符合設計要求，連接應牢固緊密。
2）、安裝在保溫管道上的各類手動閥門，手柄均不得向下。
3）、閥門安裝前必須進行外觀檢查，閥門的銘牌應符合現行國家標準《通用閥門標志》GB 12220的規定。對于工作壓力大于1.0 MPa 及在主干管上起到切斷作用的閥門，安裝前應進行強度和嚴密性能試驗，合格后方準使用。強度試驗時，試驗壓力為公稱壓力的1.5倍，持續時間不少于5min，閥門殼體、填料應無滲漏為合格。嚴密性試驗時，試驗壓力為公稱壓力的1.1倍；試驗壓力在試驗持續的時間應符合GB 50243標準要求，以閥瓣密封面無滲漏為合格。
Z41H美標法蘭閘閥性能規范
型號公稱壓力
(MPa) 實驗壓力工作溫度(℃) 適用介質
強度水（MPa）密封（水）空氣（MPa）低壓密封空氣（MPa）
ZAH-16C
Z41W-16P(R) 1.6 2.4 1.8 0.6 ≤200 硝酸類
Z41W-25P(R) 2.5 3.8 2.8 0.6 ≤200 醋酸類
Z41W-40P(R) 4.0 6.0 4.4 0.6 ≤200 硝酸類
Z41W-60P(R) 6.4 9.6 7.0 0.6 ≤200 醋酸類
Z41H美標法蘭閘閥主要零件材質
閥體/閥蓋 | ZGICr18Ni9Ti | ZG00Cr18Ni10 | ZG1Cr18Ni12M02Ti | ZG00Cr17Ni14M02 | WCB |
零件名稱 | ZGICr18Ni9Tit系列 | ZG00Cr18Ni10系列 | ZG1Cr18Ni12M02Ti系列 | ZG00Cr17Ni14M02系列 | WCB系列 |
閘板 | ZGICr18Ni9Ti | ZG00Cr18Ni10 | ZG1Cr18Ni12M02Ti | ZG00Cr17Ni14M02 | 1Cr13 |
閥桿 | 1Cr18Ni9Ti | 00Cr18Ni10 | 1Cr18Ni12M02Ti | 00Cr17Ni14M02 | 1Cr13 |
填料 | PTFE編織 | PTFE編織 | PTFE編織 | PTFE編織 | 石墨 |
墊片 | 304L＋PTFE | 304L＋PTFE | 316＋PTFE | 316L＋PTFE | 石墨 |
壓蓋 | ZGICr18Ni9Ti | ZG00Cr18Ni10 | ZG1Cr18Ni12M02Ti | ZG00Cr17Ni14M02系列 | WCB |
填料壓環 | 1Cr18Ni9Ti | 00Cr18Ni10 | 1Cr18Ni12M02Ti | 00Cr17Ni14M02 | 1Cr13 |
螺栓 | 1Cr17Ni2 | 1Cr17Ni2 | 1Cr17Ni2 | 1Cr17Ni2 | 35CrMoA |
螺母 | 1Cr18Ni9Ti | 1Cr18Ni9Ti | 1Cr18Ni9Ti | 1Cr18Ni9Ti | 45 |
Z41H美標法蘭閘閥主要連接尺寸
磅級 | 公稱通徑 | 單位 | 主要連接尺寸 | Z4/0/1外型尺寸 | |||||||
in | mm | L | D | D1 | D2 | b | z-φd | H(全開) | W | ||
150LB | 1 | 25 | in | 5 | 4.25 | 3.1 | 2 | 0.44 | 4-0.63 | 7.87 | 4.72 |
mm | 127 | 108 | 79.5 | 51 | 11.5 | 4-15 | 200 | 120 | |||
11/4 | 32 | in | 5.5 | 4.63 | 3.5 | 2.5 | 0.5 | 4-0.63 | 9.25 | 5.11 | |
mm | 140 | 117 | 89 | 64 | 13.0 | 4-15 | 235 | 140 | |||
11/2 | 40 | in | 6.6 | 5 | 3.88 | 2.88 | 0.56 | 4-0.63 | 11.22 | 7.09 | |
mm | 165 | 127 | 98.5 | 73 | 14.5 | 4-15 | 285 | 180 | |||
2 | 50 | in | 7.00 | 6.00 | 4.75 | 3.62 | 0.75 | 4-0.75 | 16.10 | 8.00 | |
mm | 178 | 152 | 120.5 | 92 | 19.1 | 4-19 | 409 | 200 | |||
21/2 | 65 | in | 7.48 | 7 | 5.5 | 4.13 | 0.69 | 4-0.75 | 17.13 | 7.87 | |
mm | 190 | 178 | 139.5 | 105 | 18 | 4-19 | 4.5 | 200 | |||
3 | 80 | in | 8.00 | 7.50 | 6.00 | 5.00 | 0.94 | 4-0.75 | 20.00 | 10.00 | |
mm | 203 | 190 | 152.5 | 127 | 23.9 | 4-19 | 570 | 250 | |||
4 | 100 | in | 9.00 | 9.00 | 7.50 | 6.19 | 0.94 | 8-0.75 | 23.20 | 10.00 | |
mm | 229 | 229 | 190.5 | 157 | 23.9 | 4-19 | 590 | 250 | |||
5 | 125 | in | 10 | 10 | 8.5 | 7.31 | 0.94 | 8-0.88 | 28.54 | 9.84 | |
mm | 254 | 254 | 216.0 | 186 | 24 | 8-22 | 725 | 250 | |||
6 | 150 | in | 10.50 | 11.00 | 9.50 | 8.50 | 1.00 | 8-0.88 | 24.80 | 12.00 | |
mm | 267 | 279 | 241.5 | 216 | 25.4 | 8-22 | 630 | 300 | |||
8 | 200 | in | 11.50 | 13.50 | 11.75 | 10.62 | 1.12 | 8-0.88 | 37.80 | 13.88 | |
mm | 292 | 343 | 298.5 | 270 | 28.5 | 8-22 | 960 | 350 | |||
10 | 250 | in | 13.00 | 16.00 | 14.25 | 12.75 | 1.19 | 12-1.00 | 45.60 | 15.70 | |
mm | 330 | 406 | 362 | 324 | 30.2 | 12-25 | 1158 | 400 | |||
12 | 300 | in | 14.00 | 19.00 | 17.00 | 15.00 | 1.25 | 12-1.00 | 54.30 | 17.70 | |
mm | 356 | 483 | 432 | 381 | 31.8 | 12-25 | 1378 | 450 | |||
14 | 350 | in | 15.00 | 21.00 | 18.75 | 16.26 | 1.38 | 12-1.12 | 60.75 | 19.70 | |
mm | 381 | 533 | 476.5 | 413 | 35 | 12-29 | 1543 | 500 | |||
16 | 400 | in | 16.00 | 23.50 | 21.25 | 18.50 | 1.44 | 16-1.12 | 68.40 | 23.60 | |
mm | 406 | 597 | 539.5 | 470 | 36.6 | 16-29 | 1738 | 600 | |||
18 | 450 | in | 17.00 | 25.00 | 22.75 | 21.00 | 1.56 | 16-1.25 | 71.10 | 23.60 | |
mm | 432 | 635 | 578 | 533 | 39.7 | 16-32 | 1959 | 600 | |||
20 | 500 | in | 18.00 | 27.50 | 25.00 | 23.00 | 1.69 | 20-1.25 | 87.20 | 26.80 | |
mm | 457 | 698 | 635 | 584 | 42.9 | 20-32 | 2214 | 680 | |||
24 | 600 | in | 20.00 | 32.00 | 29.50 | 27.25 | 1.88 | 20-1.38 | 102.3 | 29.90 | |
mm | 508 | 813 | 749.5 | 692 | 47.7 | 20-35 | 2599 | 760 |
掃一掃“二維碼”快速鏈接企業微店
推薦使用 微信 或 UC 掃一掃 等掃碼工具
微店融入移動互聯網帶來更多的商業機會。
